[admin]

The use of hydraulic hoses in high-temperature environments requires special attention because high temperatures will accelerate the aging and performance degradation of materials, thus affecting the reliability and safety of the system. This article will discuss in detail the precautions for the use of hydraulic hoses in high-temperature environments to ensure their reliability and durability under various complex conditions.

1. The impact of hydraulic hoses in high-temperature environments

Material aging: High-temperature environments can cause thermal oxidation reactions in the materials of hydraulic hoses (such as rubber), causing them to gradually lose elasticity and strength. This aging process is irreversible, and over time, the hoses will become hard and brittle and prone to rupture.

Performance degradation: High temperatures can cause changes in the physical properties of hydraulic hoses, such as reduced elastic modulus and weakened tensile strength. These changes will affect the pressure-bearing capacity and service life of the hoses.

Increased risk of leakage: Due to material aging and performance degradation, hydraulic hoses are more likely to leak in high-temperature environments. Especially at the joints, the sealing performance may be affected due to the effects of thermal expansion and contraction.

2. Choose the right material

High-temperature resistant rubber: In high-temperature environments, high-temperature resistant rubber materials such as silicone rubber or fluoro rubber should be selected. These materials can maintain good elasticity and strength at high temperatures, reducing the risk of leakage caused by thermal expansion.

Silicone rubber: has good high-temperature resistance and can remain stable in the temperature range of -60°C to +200°C.

Fluororubber: has excellent chemical corrosion resistance and high-temperature resistance, suitable for more extreme temperature environments.

Reinforcement layer material: In addition to the lining rubber, the choice of reinforcement layer material is also very important. Commonly used reinforcement layer materials include two types: wire braiding and wire winding.

Wire braiding: has high flexibility and good bending performance, suitable for dynamic applications.

Wire winding has higher pressure bearing capacity and better wear resistance and is suitable for static or low-frequency dynamic applications.

3. Add protection measures

Insulation layer: You can add an insulation layer or a high-temperature resistant protective sleeve to the outside of the hydraulic hose to reduce the time and degree of direct exposure to high-temperature environments. The insulation layer can effectively reduce the surface temperature of the hose and delay the aging process of the material.

Protective sleeve: The use of metal or non-metallic protective sleeves can further protect the hydraulic hose from external factors. The protective sleeve can not only provide physical protection but also isolate heat transfer to a certain extent.

4. Regular inspection and maintenance

Regular inspection: High temperatures will accelerate the aging process of hydraulic hoses, so more frequent inspection and maintenance are required. During the inspection, attention should be paid to whether the hose has softening, expansion, or cracks.

Appearance inspection: Observe whether there are cracks, bulges, or other abnormalities on the surface of the hose.

Pressure test: Use professional pressure testing equipment to regularly test the pressure bearing capacity of the hydraulic hose to ensure that it works within a safe range.

Timely replacement: Once the hydraulic hose is found to have obvious signs of damage or performance degradation, it should be stopped and replaced with a new hose immediately. Do not wait until the hose fails completely before taking action to avoid causing greater losses.

5. Avoid drastic temperature changes

Gradual heating: Rapid temperature changes will cause increased internal stress in the material, thereby increasing the risk of rupture. Therefore, the temperature should be gradually increased before use to avoid sudden exposure to high-temperature environments. This can be achieved by preheating the equipment or slowly increasing the system temperature.

Control the cooling rate: Similarly, the cooling rate should be controlled after shutdown to avoid rapid shrinkage of the hose due to excessive temperature differences, cracks or other damage. The cooling rate can be adjusted by natural cooling or using a cooling device.

6. Precautions for installation and use

Correct installation: The correct installation method is essential to extend the service life of the hydraulic hose. Avoid excessive bending and twisting during installation to prevent rupture due to stress concentration. At the same time, ensure that the joints are well-sealed to prevent leakage.

Avoid friction: Try to avoid friction between the hydraulic hose and other components during installation and use. Lubricants or additional sheaths can be used to reduce friction and protect the hose surface from damage.

Reasonable layout: A reasonable layout of hydraulic hoses can reduce additional stress caused by external forces. For example, the hose can be fixed on a bracket to prevent it from swinging freely; or it can be placed away from heat sources to reduce the chance of heat exposure.

7. Other precautions

Avoid direct sunlight: Long-term direct sunlight will cause the surface temperature of the hydraulic hose to rise and accelerate the aging process. Therefore, try to avoid exposing the hose to the sun, or take sunshade measures.

Pay attention to ventilation and heat dissipation: Good ventilation can help dissipate heat and reduce the temperature around the hydraulic hose. When designing the system, ventilation and heat dissipation should be considered to ensure sufficient air circulation.

Comply with operating procedures: Operate and maintain in strict accordance with the operating procedures of the equipment manufacturer, and do not change settings or overload at will. Any violation of regulations may cause damage to the hydraulic hose and shorten its service life.

The use of hydraulic hoses in high-temperature environments requires special attention to material selection, protective measures, regular inspections, and maintenance. By rationally selecting and using hydraulic hoses, their service life can be effectively extended and the reliability and safety of the system can be improved. I hope that the content provided in this article can help readers better understand and cope with the challenges of hydraulic hoses in high-temperature environments.

As leading hydraulic hose companies, we are well aware of the importance of using hydraulic hoses in high-temperature environments. Therefore, we are committed to the research development, and production of high-quality high-temperature-resistant hydraulic hoses to meet the needs of our customers. Our hoses are made of advanced materials and manufacturing processes and have excellent temperature resistance, pressure resistance, and wear resistance. At the same time, we also provide comprehensive technical support and perfect after-sales service to ensure that customers have no worries during use.

http://www.tianyiindustry.com
Zaozhuang Tianyi Industry Co., Ltd.,

[Author]

Posts